2018 Audi Q5

My 2018 Audi Q5 became disabled after liquid intrusion affected the gateway control module, which is the condition addressed by Audi Safety Recall 90S9. At the time of the failure, I was traveling away from home and was unaware that my vehicle had an open recall. Because the vehicle was disabled, it was taken to an independent repair facility for diagnosis (we were in a small mountain town on a Sunday). The independent facility accessed/opened the gateway module during its good-faith diagnostic effort after the vehicle had already failed. The vehicle was subsequently presented to Audi Reno. Audi refused to perform the recall repair/replacement because the gateway module had previously been accessed by the independent repair facility. I escalated the matter to Audi of America under case 07709194. Audi acknowledged in writing that the module was accessed as part of a good-faith diagnostic effort while I was stranded and unaware of the open recall. However, Audi continues to deny recall coverage based upon the prior diagnostic access. I have asked Audi to identify the specific written provision of Safety Recall 90S9 stating that diagnostic access to an already-failed gateway module disqualifies the vehicle from the safety recall, but Audi has not provided such a provision. I am reporting this because my vehicle experienced the safety condition addressed by the recall, yet Audi refused to perform the recall remedy based on diagnostic activity that occurred only after the vehicle had already become disabled.

After one year of use, the car seat developed a sudden defect. An internal rod slid out of place, protruding from the side of the car seat by about an inch. I reported the issue to Graco, and they confirmed this car seat defect is a child safety risk, and in fact the car seat is no longer safe for use. According to the Graco Consumer Care representative: "I do apologize, but the rod protruding from the car seat is not normal and presents a safety hazard. Unfortunately, this is not a replaceable part, and the issue cannot be repaired without replacing the entire car seat." I have a friend who experienced the same issue, and worry that the Graco Turn2Me is prone to sudden safety defects. We have kept the broken car seat and it is available for inspection. The car seat has not been inspected by the manufacturer, police, insurance, or anyone else.

Driving through the expressway a metal noice from the bottom of my car. One of the coil spring was out of the base and the other was broken. As the Audi dealer, the extended warranty doesn’t want to paid due to a corrosion on the bottom of the car. I’m live and drive close to the beach. They gave me thousands excuses to not fix it. My car has 60,000 miles and is from 2018. I was reading that those car may not be coated with special wax for corrosion.

The sunroof drainage system on my 2018 Audi Q5 failed to properly channel water away from the vehicle, resulting in significant water intrusion and approximately $6,000 in damage. The problem was confirmed by an authorized Audi dealership after the vehicle was brought in for inspection in August 2026. I am concerned that this represents a design or engineering defect in the sunroof drainage system rather than ordinary wear. A drainage system intended to remove water should not allow water to enter areas of the vehicle where it can damage electrical components or other systems. Water intrusion into these areas could potentially create electrical failures or other safety-related problems. The vehicle was inspected by an authorized Audi dealer, and Audi of America was contacted regarding the issue. Audi declined to cover the repairs. There were no clear warning lights or messages alerting me that the drainage system was failing before the water intrusion and resulting damage were discovered. The vehicle and affected components can be made available for inspection if necessary. I am submitting this complaint because I believe NHTSA should investigate whether similar sunroof drainage failures and resulting water intrusion have occurred in other Audi Q5 vehicles and whether this represents a broader vehicle safety defect.

I have a 2018 Audi Q5, VIN [XXX]. I am reporting a water intrusion/electrical defect involving the rear trunk area and the Comfort Control Module. My vehicle is within the model range affected by the water-intrusion recall 90S9. I want Audi to investigate whether the water intrusion that damaged my vehicle is related to the recall or a known manufacturing defect, and I am requesting that Audi cover the inspection, repair, and related expenses.It is unsafe driving the car as it is, and I can't afford the repairs. Audi dealer-hip in Alentown Pa diagnosis the car and found the problem. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Multiple electrical failures that control numerous safety systems, such as airbags, Collision avoidance, speed control, etc. Airbags will not activate in a collision. Vehicle will shut off at highway speeds, resulting in loss of steering control. The vehicle has been inspected by an Audi dealer. Multiple warnings on dash came on when the issue occurred.

Incident Description: While accelerating from a red light during rush hour, the vehicle suffered a sudden, catastrophic loss of steering control. The steering wheel locked completely and could not be turned. Simultaneous loud, long beeping and dashboard warnings appeared, stating: "Steering malfunction stop the vehicle immediately." The vehicle was immobilized in the middle of a highly congested, complex 5x5 intersection. Local police had to shut down traffic until the vehicle could be cleared. Safety Risk: Stalling abruptly in a major intersection during rush hour created an immediate risk of a multi-car rear-end pile-up. This jeopardized the safety of the driver and multiple children who were inside the vehicle, who faced a severe personal injury risk whether they remained trapped in the active roadway or attempted to exit. Diagnosis, Cost, and Recall Context: The vehicle was towed to an authorized dealership. Diagnosis revealed significant water intrusion inside the steering wheel wiring harness. Draining the water cleared the error and the vehicle become operational, but the dealership quoted $6,000 in repairs to replace the steering components completely out-of-pocket cost. Please note it appears the $6,000 quote will be out-of-pocket for catastrophic safety defects although they may be known issues for the same make and model years: Prior Gateway Recall: This vehicle’s VIN was previously impacted by the Gateway module recall (where water intrusion triggers a limp mode). That recall was redeemed prior to this event, and my understanding the repair should have prevented moisture intrusion. There seems to be a history on this make and model for known moisture intrusion causes critical issues. U45 Warranty Exclusion: The manufacturer issued a warranty extension for this exact steering failure on this same make and model years. However, this specific VIN was excluded from coverage, despite it being within the parameters.

Description of Incident and Safety Defect:Failed Component & Inspection Availability: The gateway control module, located in an unsealed floor compartment under the rear seat, failed due to liquid/moisture intrusion. The damaged module and vehicle are fully available for inspection upon request.Safety Risk: The sudden short-circuit of this module forced the vehicle into an immediate emergency "limp mode" and partial drivetrain shutdown while actively driving on the road. Unexpectedly losing engine power and throttle responsiveness in active traffic put my safety and the safety of surrounding drivers at an immediate, severe risk of a collision.Dealer / Independent Confirmation: The failure has been officially confirmed by an authorized Audi dealership service center. However, the dealer refused to perform a free safety repair because Audi has excluded my specific VIN from the active recall list.Prior Inspections: Outside of the diagnosing Audi dealership service center, the vehicle and failed component have not yet been inspected by the manufacturer, police, or insurance representatives.Warning Lamps & Prior Symptoms: Immediately prior to the drivetrain failure, the dashboard lit up with sudden error messages and warning lamps regarding a critical system malfunction. There were no gradual symptoms or warning signs leading up to this incident; the catastrophic module failure occurred suddenly due to moisture contacting the unsealed component.Summary Assessment:This vehicle has suffered the identical engineering defect and hazardous failure mode detailed in NHTSA Recall Campaign 21V-947 (Audi Recall Code 90S9). Audi’s current recall window is too narrow. It must be expanded to include all 2018 Audi Q5 vehicles experiencing this exact, catastrophic safety failure, regardless of their production date cut-offs. To date the car has 89924 miles

While driving the vehicle after a bump in a pot-hole there was loud clunking noise from the engine compartment and car stopped suddenly. There was a risk of getting hit by the car from behind. Car was towed to Audi Service Center and found to have a Connecting Rod Bearing Failure damaging the whole engine. The act is still at the repair shop and should be available for inspection. It was inspected by the authorized Audi Service center. Insurance advisor will be taking look at it also. There was no warning, messages, or any other symptoms of any problem prior to the incident.

XXX My wife drive her 2018 audi q5 2.0 on express way with mother([XXX]),the car suddenly stall and lost all power ,because car bcm2 module has suffered liquid damage due to known vehicle design defect, towing to nearest repair shop change new bcm2 module and fix wire spend near $4000.00 dollars . INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

I was pulling into (my usual) handicapped parking space, at a slow speed. As I approached the curb my brakes did NOT respond to stop my car. Not only did my brakes not respond, the car actually sped up - going up the curb and hitting the handicapped sign pole. The pole broke and stopped my vehicle! I was afraid my (out of control) vehicle would keep going through a store front - it did not. Folks gathered around- thinking I had put my foot on the gas . I DID NOT put my foot anywhere except on my BRAKES …which went ‘mushy’ . would not stop my vehicle. My research has found similar incidents reported by other drivers. I am NOT ALONE. Of course the dealership could not reproduce the incident. But they did suggest many other services for a car with 60,000 miles. The AUDI dealership took NO responsibility for the incident. There was a recall on the master cylinder that was supposedly handled before I took delivery of the vehicle in January 2019. Audi denied that anything was currently amiss with my master cylinder. There was a warning message when I tried to start my car about a week before. Because it made no sense - like your tires are low - I dismissed it as just a check engine light ‍♀️ I honestly can’t remember what that ‘odd’ warning said‍♀️ I’m not alone in reporting this - I’m almost afraid to drive my car

My 2018 Audi Q5 experienced significant water intrusion due to a failure of the panoramic sunroof drain system. Water entered the vehicle interior and traveled down into the electrical compartment, submerging the comfort module and damaging multiple wiring harnesses. This caused the vehicle to become inoperable and unable to start. Audi has issued Technical Service Bulletin 2075969/2 describing this exact defect. The bulletin states that the sunroof drain hoses can be kinked during factory installation of the headliner, which blocks drainage and causes water to enter the vehicle. This is a manufacturing defect affecting multiple model years of the Audi Q5. In my case, the water intrusion caused electrical failure, loss of vehicle function, and required thousands of dollars in repairs. Audi declined to cover the defect and stated the vehicle was not maintained on schedule, even though maintenance has no relationship to kinked or improperly routed sunroof drains. This defect poses a safety risk because water intrusion into electrical components can cause sudden vehicle failure, electrical shorts, corrosion, and loss of critical systems. The failure occurred without warning. I am reporting this because the issue appears to be widespread, documented by Audi, and has the potential to disable vehicles unexpectedly.

I wrote Audi to request escalation of an unresolved issue involving my 2018 Audi Q5, related to Safety Recall 90S9 (NHTSA Campaign 21V947000) for the gateway control module. Summary of the issue: My vehicle recently experienced a complete gateway control module failure due to water intrusion. I lost steering and brake assist warnings while driving, and the vehicle would not restart after being pulled over safely. It was towed first to the nearest Audi mechanic who diagnosed the issue as Recall 90S9. We then contacted Audi Memphis for inspection by them since it was a recall issues and paid a 2nd towing charge. Audi Memphis (owned by Gossett Motor Cars) said they could not do anything until they looked at the car. I have since obtained a copy of the original repair order from when Recall 90S9 was performed on my vehicle. The vehicle at the time of recall repair was owned by my Mother. The recall requires two remedies: (1) installation of a protective cover over the gateway control module, and (2) sealing of an underbody seam on vehicles produced before September 2021. The repair order shows a technician comment reading "INSF" next to the seam sealant line item, which indicates the sealant application was noted as insufficient at the time of the original recall service. Despite this documentation, and despite towing my vehicle in specifically for a 2nd inspection, Audi Memphis has stated they have no findings and no liability for the current failure. Given that: • My vehicle is included in the affected range for Recall 90S9, • The original repair order appears to document an incomplete or insufficient sealant application, and • Audi's own 90S9 technical bulletin states that damages resulting from improper repair or failure to follow the work instructions are the dealer's responsibility, I am requesting that this case be escalated for review. The current gateway control module repair be repaired at no cost to me. I currently have no working vehicle.

The dashboard displayed a solid red brake light with a flashing warning “stop vehicle safely” light. A professional diagnostic scan confirmed a permanent hard fault on the ABS control Module (J104) and Hydraulic Unit (N55). The vehicle has only 66,755 miles. Independent repair shops cannot service this unit because it requires highly restricted, specialized Audi factory programming and coding software, forcing consumers to face massive dealership replacement costs for a premature electronic failure ona critical safety system.

The contact owns a 2018 Audi Q5. The contact stated while driving at an undisclosed speed, the engine seized. No warning lights were illuminated. The contact stated while attempting to start the vehicle, the vehicle failed to start. The contact replaced the battery. The contact stated while attempting to start the vehicle, the vehicle failed to start. The vehicle was towed to an independent mechanic, however the vehicle was not diagnosed. The independent mechanic attempted to start the vehicle, however the vehicle failed to start. The independent mechanic inspected the vehicle and noticed that the gateway control modular was moist. The contact was informed that the gateway control module had become moist because of the broken seal, the vehicle shut down. The contact stated that the contact's wife had spilled a liquid substance into the vehicle. In addition, the contact was provided pictures of the corrosion. The contact referenced an unknown recall which had a similar failure description, however the contact's VIN was not associated. The dealer was made aware of the failure. The contact was informed that the repair was not covered under the recall. In addition, the contact was informed that the unknown recall only covered the seal. The contact was informed that the recall did not cover the replacement of the gateway control modular. The manufacturer was made aware of the failure and a case was filed. The contact was informed that the repair of the corroded seal was covered under the recall. The contact was advised to take the vehicle to the dealer for diagnostic testing. The failure mileage was approximately 103,000. VIN was unavailable.

I was driving home from the farmers market with my two young kids. I was turning left at a busy intersection when the engine died and an engine warning flashed on the dash (I don't recall the exact message; it sounded catastrophic). There were no "check engine" or any other warning messages prior to the incident. I was able to restart the car immediately and give it a lot of gas to get out of the intersection - thank goodness - but didn't feel it was safe to drive the full 1 mile home, as there are several inopportune locations for an engine to die along the route, so I parked it in a residential neighborhood and walked home with my kids. My instinct there seems correct as it would not start again thereafter. I got it towed on the Monday and the mechanic called me to tell me that a piston had broken off in the engine and there is complete engine failure. I've attached a photo he took. This is a car we've had for 5 months with only 47,000 miles on it, regular service according to Carfax, and full/clean oil. No error messages or warnings prior. It was really scary to be in a busy intersection with a dead engine and young kids in the car.

Title - Sudden Loss of Steering Control While Driving – 2018 Audi Q5 (Aug 2024) While driving my 2018 Audi Q5 at normal road speeds, the vehicle experienced a sudden and complete loss of power steering assist. A dashboard alert stating “Power Steering Malfunction” appeared simultaneously with an immediate and severe increase in steering effort, making the steering wheel extremely difficult to turn and effectively resulting in a loss of steering control. This incident occurred on a public roadway while I was transporting my family, including two young children (ages [XXX] and [XXX] ). The uncommanded loss of steering assist created an immediate and serious safety hazard and could have resulted in a crash, serious injuries, or fatalities to vehicle occupants and others on the road. I was able to bring the vehicle to a stop and subsequently to the dealership, only with significant effort and risk. There were no prior warning lamps, noises, reduced steering assist, or other symptoms before the failure. The malfunction was abrupt and occurred without any advance indication. The vehicle had approximately 39,000 miles at the time, which is well below what would reasonably be expected for a power steering rack failure. The vehicle was not modified or abused and was driven under normal conditions. Audi dealership confirmed failure of the electric power steering system and diagnosed the issue as a power steering rack failure requiring full replacement. The repair was completed only after the vehicle became unsafe to operate. The removed component may be available through the servicing dealer or Audi of America for inspection upon request, and I have retained all repair documentation. Audi of America was notified of this incident after the repair but declined responsibility. Based on subsequent research, I am aware of multiple similar reports involving Audi Q5 power steering failures. I am submitting to assist NHTSA in determining whether this issue poses a broader risk. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

I was pulling slowly into a parking space at a grocery store, with my right foot on the brake, nearly stopped. Then the car rapidly and suddenly accelerated unintentionally. The car jumped over a bush, a median, rammed into a parked car, pushing it across the next parking lane into a third car. The third car, in turn, bumped a fourth car. Safety: The air bags did not deploy. The potential for significant injury to me, nearby pedestrians and people in cars was extremely high. Luckily, I was able to brace myself sufficiently, there were no pedestrians nearby and no one was in any of the cars. There were no warning lights, beeps, messages or any other information to indicate a defect or potential malfunction.

The rear view camera is not operating when shifting to reverse. I can demonstrate this malfunction at any time to anyone. Driver is unable to detect short objects or small children directly behind the vehicle. The problem was confirmed by the dealer during a service visit. At that time, the service technician checked power and ground to the control unit and verified good. Attempted calibration for camera, vehicle would not calibrate. The vehicle has not been inspected by any other agencies. There were no warning messages, or lamps or any other symptoms prior to the failure.

The Seat Occupancy Detection System is malfunctioning. The passenger airbag warning light activates when a passenger occupies the passenger seat and the passenger overhead reading light remains on when the seat is occupied including overnight. These are established symptoms of Seat Occupancy Detection System failure. The manufacturer issued a warranty extension specifically covering this defect for 10 years and unlimited miles. When the vehicle was presented at an authorized dealer for diagnosis and repair under the warranty extension, the service advisor deliberately omitted the airbag warning light symptom from the repair order and inserted pre-emptive warranty denial language before any diagnosis was performed. The airbag system malfunction remains unrepaired despite an active manufacturer warranty extension covering this exact defect. The dealer’s failure to properly document and address an airbag warning light constitutes a safety concern that NHTSA should investigate.