2016 Jeep Wrangler

ABS Control Module stopped working with several warning lights showing on dash display. After 12 months the dealer is unable to supply a replacment part or a possible date when a new part might be available.

The ABS module on my jeep has failed. I've been put on a list to get a replacement part but have been on the list for 10 months with no indication of when my parts order will be fulfilled. The failed ABS module caused the BRAKE, ABS and TCS warning lights to be on. I am driving a vehicle under unsafe conditions and the manufacturer does not care.

My 2016 Jeep Wrangler is experiencing an ongoing problem with the ABS/braking system and wheel-speed sensor. The ABS/brake warning light comes on intermittently, particularly when turning right and during hot weather. The vehicle has NOT been repaired for this problem. I am reporting it because I am concerned that there may be a defect involving the wheel-speed sensor, sensor wiring/connection, wheel hub, or ABS system. Because these components are connected to the vehicle’s anti-lock braking and stability/traction-control systems, I am concerned about the safety of continuing to drive the vehicle. I would like this problem investigated as a potential safety defect. I am also requesting that NHTSA review whether other 2016 Jeep Wrangler owners have reported similar ABS, brake warning light, or wheel-speed sensor failures and determine whether a safety recall is warranted. There was no accident it just started happening on its own.

ABS Brake Sensor is on and the ABS Module needs to be replaced, however there are a lot of other people out there with this same issue and nobody can keep up with the parts to fix the problem. This should be a recall for all Jeeps 2009-10018

The contact owns a 2016 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, the vehicle experienced an ABS module failure. The ABS and traction control warning lights were illuminated. The dealer was contacted and diagnosed the vehicle with ABS control module failure; however, the part to repair the vehicle was not available. The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time to provide the parts for the repair. The manufacturer was made aware of the failure but was unable to determine when parts for the repair would be available. The failure mileage was approximately 80,000.

The ABS control module has internal problem which shuts down the module. Results of the module shut down includes: -The stability and traction systems are offline. -A failure in the ABS module or hydraulic unit. -Cruise Control inoperable. -The module no longer modulates brake pressure, which can result in brakes locking. Currently, Mopar has stopped production of this item, so there is no method to replace a failed or non-working module with an original part.

Code C2200 Multiple visits to shop. Part is on indefinite backorder. Brakes lock up when quick needed, traffic/other driver pull out in front of me Showed up 4 months ago

I was driving down the road in a snow storm when all of a sudden the vehicle started swirling all over the road. I pulled over and looked underneath and something was hanging down. I had no choice but to drive it slow less than 10mph to make it home as it was also making a hard jumping. Once there I had my mechanic come look at it and the drive shaft was busted. I am extremely luck that this happened during a snow storm because if not I may have rolled the vehicle as the steering was greatly affected.

ABS module is bad, shooting codes on dash, disable cruise, worried about issues with braking.

The ABS Module is non operative and has been on back order for over 3 years from the Dealership.

My 2016 Jeep Wrangler will buck and jerk when on the highway. I’ll be going a steady speed, not changing speed. I feel the car slow down and stomp on the gas but it goes all the way to the floor and nothing happens. When I try to go into the break down lane, the steering wheel locks up and won’t turn. Usually I take the key out then put it back in the ignition and it starts no problem. Recently, the engine has been stalling when I put the key back in the ignition. I usually have to take the key out and sit on the side of the highway for 5 minutes before starting it up with no problem. This has happened too many times than I’d like to admit. Take it to the shop, no codes come up. Sometimes the engine light will turn on when this happens, other times it doesn’t.

ABS module failure

The abs module malfunctioned and there’s no replacement. It’s been on back order for a couple years

ABS module failure without cause. New modules no longer being produced. Lack of anti braking system is a huge safety concern. Vehicle was looked at by a mechanic. Brake light, stability control light, and ABS light all came on at the same time at the time of failure. Vehicle was in park and turned on at the time of failure.

The contact owns a 2016 Jeep Wrangler. The contact stated while the vehicle was parked, the antilock brake system warning light was illuminated. The vehicle was taken to an independent mechanic where it was diagnosed that the antilock brake system needed to replaced however, the dealer recommended that the vehicle be taken to a dealer. The vehicle was not repaired. The vehicle was taken to a dealer where it was diagnosed once again that the antilock brake system needed to be replaced however, the parts were not available. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 76,000.

The contact owns a 2016 Jeep Wrangler. The contact stated while driving at an undisclosed speed, the ABS and traction control warning lights illuminated. The vehicle was taken to an independent mechanic where it was diagnosed with a failed ABS module. The contact was informed that the ABS module needed to be replaced. The vehicle was not repaired. In addition, the contact was informed that the parts were in back order indefinitely. The contact was advised that she could drive the vehicle at her own risk. The manufacturer was not made aware of the failure. The failure mileage was approximately 67,108.

I bought Jeep from dealership gas keeps overflowing out of tank during fill ups. Check engine light now on

The ABS module (68259556AD) on my 2016 JKU is not working (code C2200) and the part is not available anywhere. I tried buying online and reaching out to a dealership, but everyone acknowledges Stellantis doesn’t have the part available. There are posts on Jeep forums from 2023 from people with the same issue which is causing their Jeeps to go into limp mode at highway speeds. I feel unsafe driving my car and there’s no current way to fix this issue.

The ABS module has gone out with replacement parts on backorder and not being manufactured for a lengthy time. This is caused my jeep to go into limp mode since August 2025. There has not been a resolution to solve this problem at this time. Even to have it refurbished or rebuilt has not been an option due to most companies no longer working on this part.

I have a 2016 jeep wrangler and I was trying to get it fixed but the dealership said it was the abs module and that they could not get one in because they are on back order because they warehouse that provides the chips for them burned down. I was then told that it is not promised to when they will be available and then they tried to turn around and ask me did I want to trade it in. So now I am stuck still paying for the jeep and I can not drive it because of the abs module. I understand life happens but the manufacture should have called a recall or something because people are not going to be able to drive their vehicles but still have to pay for them and I am sure no one wants to start over on a new vehicle when they have paid so much on their current one.